Collection: Truck Wiring Kits (27)

The Y-Splitter complete with 2-pin superseal connections, is the ideal solution for wiring multiple low power Lazer Lamps avoiding the need for additional wiring kits run in parallel. The splitter is an ideal solution for wiring 3 or more lights, where the power rating of each light is 75W or less, and a corresponding 4-Lamp Wiring Kit doesn’t already exist for example. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: ST2 ST4 ST6 Triple-R 750 Triple-R 850 Linear-6 Linear-12 Sentinel 7''

• Y-splitter for adapting Single Lamp connection to Two Lamp setup
• Suitable for lamps 75W or less
• 2-pin superseal connections

The 3m cable extension kit is ideal for custom builds and mounting which requires additional wiring to the lights. Includes IP68 connectors at either end. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Carbon-2 (Spot / Drive) Carbon-4 (Spot / Drive) Carbon-6 (Spot / Drive) RP Hyperspot Utility-50 with Beacon Utility-50 with Red Tail Light Utility-80 HD with Variable Brightness

• 3m cable extension
• Includes 4-pin Deutsch DT connectors
• Suitable for Carbon-6, RP Hyperspot and Utility-80 HD with Variable Brightness
• Compatible with any Deutsch DT Wiring Kit

The 3m cable extension kit is ideal for custom builds and mounting which requires additional wiring to the lights. Includes IP68 connectors at either end. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: T-16 Evolution T-24 Evolution T-28 Evolution Triple-R 16 Elite Triple-R 24 Elite Triple-R 28 Elite

• 3m cable extension
• Includes IP68 Connectors
• Suitable for all non E-mark approved Lazer products (excluding Linear-48)
• Compatible with Single-Lamp Wiring Kit (High Power, 12V)

The 3m cable extension kit is ideal for custom builds and mounting which requires additional wiring to the lights. Includes IP68 connectors at either end. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Triple-R 1000 Beacon

• 3m cable extension
• Includes 6-pin TE Superseal connectors
• Suitable for Triple-R Beacon products
• Compatible with Lazer Beacon Wiring Kit (12V)

The 3m flat cable extension kit is ideal for custom builds and mounting which requires additional wiring to the lights. Includes IP68 connectors at either end. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring into your vehicle system Compatible with: ST Evolution (All Products) Triple-R 750 Elite (Gen2) Triple-R 850 Elite (Gen2) Triple-R 1000 Elite (Gen2) Linear-6 (Std / Elite) Linear-12 (Std / Elite) Linear-18 (Std / Elite) Linear-36 Linear-42 Linear-48 Sentinel 7'' Sentinel 9'' Elite

• 3m Cable Extension
• Includes IP68 Connectors
• Suitable for ST, Linear and Triple-R lamps (ECE approved models only)

The 3m cable extension kit is ideal for custom builds and mounting which requires additional wiring to the lights. Includes IP68 connectors at either end. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Triple-R 750 Triple-R 850 Triple-R 1000 Triple-R 1250 Linear-12 Elite (with Position Light) Linear-18 Elite (with Position Light) Sentinel 7'' Elite Sentinel 9'' Sentinel 9'' Chrome Sentinel 9'' Elite (with Position Light)

• 3m cable extension
• Includes 3-pin TE Superseal connectors
• Suitable for all E-mark approved Lazer products (with Position Light)
• Compatible with any Wiring Kit (Position Light, 12V)

The ideal solution for wiring 4x Lazer Carbon-6 (Gen3) High Performance LED Driving Lights, where the vehicle side connection is compatible with an ITT Cannon Connector. The resulting setup is quick, easy, and reliable with Deutsch DT06-4S lamp connectors and no configuration procedures. The kit features 1.85m of flex on the lamp cable(s) to the 8-pin Trident Ringlock ITT Cannon Connector (compatible with Skoda R5 rally cars as an example) Additional signal wires from the ITT Connector are included for operation of lamps’ in either: ‘Fog’ mode (purple wire), or ‘E-mark’ mode (green wire). All Carbon-6 (Gen3) LED Driving Lights feature a corresponding built-in DT04-4P Deutsch Connector (with gold plated solid DT contacts). Compatiable with: - Carbon-6 DRIVE (Gen3) - Carbon-6 SPOT (Gen3)

• Four-Lamp Wiring Kit for Carbon-6 (Gen3) LED spotlights / 4-Way Rally Pod System
• 2m cable length
• ITT Connector connections
• Additional extension cable for Fog and E-Mark modes
• Braided cable sections for added protection in engine bay

The ideal solution for wiring 4x Lazer Carbon-6 (Gen3) High Performance LED Driving Lights, where the vehicle side connection is compatible with an DT04-08 Deutsch Connector. The resulting setup is quick, easy, and reliable with Deutsch DT06-4S lamp connectors and no configuration procedures. The kit features 3.2m of flex on the lamp cable(s) to the 8-pin DT04-08 Connector (compatible with Citroen C3 rally cars as an example). Additional signal wires from the DT04-08 Connector are included for operation of lamps’ in either: ‘Fog’ mode (purple wire), or ‘E-mark’ mode (green wire). All Carbon-6 (Gen3) LED Driving Lights feature a corresponding built-in DT04-4P Deutsch Connector (with gold plated solid DT contacts). Compatiable with: - Carbon-6 DRIVE (Gen3) - Carbon-6 SPOT (Gen3)

• Four-Lamp Wiring Kit for Carbon-6 (Gen3) LED spotlights / 4-Way Rally Pod System
• 3.2m cable lengths
• DT04-08 Deutsch connections
• Additional extension cable for Fog and E-Mark modes
• Braided cable sections for added protection in engine bay

The ideal solution for wiring four Lazer high performance LED lights, most commonly on pick-up trucks where the requirement is for 2x lights at the front of the vehicle, and 2x lights on the roof/sports bar. Only suitable where lights without additional position light function are being used. The setup is quick, easy, and reliable with 2-pin superseal connection and no configuration procedures. The kit features a 12V relay, 35A fuse, a battery terminal at one end, and 1.5m and 6.5m of flex on the lamp cables, and allows for the operation of Lazer products in parallel with the standard high beam driving lights on your vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: ST Evolution (All Products) Triple-R 750 Elite Triple-R 850 Elite Triple-R 1000 Elite Linear-6 (Std / Elite) Linear-12 (Std / Elite) Linear-18 (Std)

• Four-Lamp Wiring Kit for Lazer driving lights (2-Pin, Superseal connections)
• 1.5m / 6.5m cable lengths
• Includes 12V relay and 35 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• 2-pin Superseal connections
• Allows for operation of lights in parallel with standard high beam lights
• Conduit cable sections for added protection within engine bay

The ideal solution for wiring 2x Lazer Carbon-6 (Gen3) High Performance LED Driving Lights, where the vehicle side connection is compatible with an ITT Cannon Connector. The resulting setup is quick, easy, and reliable with Deutsch DT06-4S lamp connectors and no configuration procedures. The kit features 1.85m of flex on the lamp cable(s) to the 8-pin Trident Ringlock ITT Cannon Connector (compatible with Skoda R5 rally cars as an example) Additional signal wires from the ITT Connector are included for operation of lamps’ in ‘E-mark’ mode (green wires). All Carbon-6 (Gen3) LED Driving Lights feature a corresponding built-in DT04-4P Deutsch Connector (with gold plated solid DT contacts). Compatiable with: - Carbon-6 DRIVE (Gen3) - Carbon-6 SPOT (Gen3)

• Two-Lamp Wiring Kit for Carbon-6 (Gen3) LED spotlights
• 2m cable length
• ITT Connector connections
• Additional extension cables for E-Mark mode
• Braided cable sections for added protection in engine bay

The ideal solution for wiring a pair of Lazer Carbon-6 (Gen3) / RP Hyperspot High Performance LED Driving Lights. The setup is quick, easy, and reliable with Deutsch DT06-4S connectors and no configuration procedures. The kit features a 12V relay, fuse, and battery terminal at one end, and 2.35m of flex on the lamp cable(s). The wiring kit allows for the operation of two lamps via an on/off switch which can be mounted inside your vehicle’s cockpit. Compatiable with: Carbon-2 (Spot / Drive) Carbon-4 (Spot / Drive) Carbon-6 (Spot / Drive) RP Hyperspot Utility-50 with Beacon Utility-50 with Red Tail Light Utility-80 HD with Variable Brightness

• Two-Lamp Wiring Kit for Lazer High Performance LED Lights (see product text for compatibility)
• 2m cable lengths
• Includes 12V relay and 25 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• Deutsch DT06-4S connections
• Includes on/off switch for independent operation of lights
• Braided cable sections for added protection in engine bay

Two-Lamp wiring kit for Lazer Lamps High Performance LED lights. The setup is quick, easy, and reliable with 2-pin Deutsch connection and no configuration procedures. The kit features a 12V relay (in waterproof housing), fuse, a battery terminal at one end, and 6.5m of flex on the lamp cable, and allows for the operation of Lazer products either in parallel with the standard lighting on the vehicle, and/or via an independent switch which can be mounted inside your vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Linear-24 Flood Utility-25 Utility-25 MAXX Utility-45 Utility-50 Utility-80 HD (Heavy Duty) RP Spot

• Two-Lamp Wiring Kit for Lazer High Performance LED Lights (see product text for compatibility)
• 6.5m cable lengths
• Includes 12V relay and 20 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• 2-pin deutsch connections
• Includes on/off switch for independent operation
• Braided cable sections for added protection in engine bay

Two-Lamp wiring kit for Lazer Lamps High Performance LED lights. The setup is quick, easy, and reliable with 2-pin Deutsch connection and no configuration procedures. The kit features a 12V relay (in waterproof housing), fuse, a battery terminal at one end, and 2m of flex on the lamp cable, and allows for the operation of Lazer products either in parallel with the standard lighting on the vehicle, and/or via an independent switch which can be mounted inside your vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Linear-24 Flood Utility-25 Utility-25 MAXX Utility-45 Utility-50 Utility-80 HD (Heavy Duty) RP Spot

• Two-Lamp Wiring Kit for Lazer High Performance LED Lights (see product text for compatibility)
• 2m cable lengths
• Includes 12V relay and 10 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• 2-pin deutsch connections
• Includes on/off switch for independent operation
• Braided cable sections for added protection in engine bay

The ideal solution for wiring a pair of Lazer high performance LED spotlights, which also feature integrated Side/Position Light and Beacon function. The setup is quick, easy, and reliable with 6-pin superseal connections and no configuration procedures. The kit features a 12V relay (in waterproof housing), 30A fuse, a battery terminal at one end, and 3.5m of flex on lamp cables, and allows for the operation of Lazer products in parallel with the standard lighting on the vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring into your vehicle system. Compatible with: Triple-R 1000 with Beacon

• Two-Lamp Wiring Kit for Lazer products with integrated Position Light and Beacon function
• 3.5m cable lengths
• Includes 12V relay and 30 amp fuse
• Superseal connections
• High beam trigger wire allows for operation of lights in parallel with standard high beams
• Conduit cable sections for added protection in engine bay

Two-Lamp wiring kit for Lazer Lamps High Performance LED lights. The setup is quick, easy, and reliable with 3-pin Superseal connection and no configuration procedures. The kit features a 12V relay (in waterproof housing), fuse, a battery terminal at one end, and 1.2m of flex on the lamp cable, and allows for the operation of Lazer products either in parallel with the standard lighting on the vehicle, and/or via an independent switch which can be mounted inside your vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Air-130 Elite Sentinel 9'' Elite (with position light) Linear-18 Elite (with position light) Triple-R 1250

• Two-Lamp Wiring Kit for Lazer High Performance LED Lights (see product text for compatibility)
• 1.2m cable lengths
• Includes 12V relay and 40 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• Superseal connections
• Includes optional on/off switch for independent operation of high beam
• Braided cable sections for added protection in engine bay

Two-Lamp wiring kit for Lazer Lamps High Performance LED lights. The setup is quick, easy, and reliable with 3-pin Superseal connection and no configuration procedures. The kit features a 12V relay (in waterproof housing), fuse, a battery terminal at one end, and 1.2m of flex on the lamp cable, and allows for the operation of Lazer products either in parallel with the standard lighting on the vehicle, and/or via an independent switch which can be mounted inside your vehicle. All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system. Compatible with: Linear-6 Elite+

• Two-Lamp Wiring Kit for Linear-6 Elite+ High Performance LED Lights
• 1.2m cable lengths
• Includes 12V relay and 30 amp fuse
• Relay holder approved to IP53 when mounted in a vertical (upright) orientation
• Superseal connections
• Includes optional on/off switch for independent operation of high beam
• Includes momentary switch for easy operation of light modes
• Braided cable sections for added protection in engine bay